GPA conversion

Post Reply
tomar
Posts: 19
Joined: Thu Nov 08, 2007 5:28 pm

GPA conversion

Post by tomar » Thu Nov 08, 2007 6:30 pm

Hi,

I am studying Applied Math in Canada, and hoping to get into a top US physics school. However, we don't use GPAs, we use %. I have a 93.5% Math/Physics Average and 89% overall average. What GPA does that translate to? Anyone know? Here usually A is 85-90% and A+ is 90+

Peace

User avatar
butsurigakusha
Posts: 293
Joined: Sun Oct 07, 2007 8:05 pm

Post by butsurigakusha » Thu Nov 08, 2007 7:05 pm

I am not really sure how to convert. Here is our (approximate) system:

A = 4
A- = 3.7
B+ = 3.4
B = 3
B- = 2.7

or so.

At my school, in a class, an A typically requires 93%, sometimes a little more, and sometimes a little less. We don't have A+ at my school, and I would guess most schools don't have them either.

I would guess that both of your averages would probably fall somewhere between 3.7 and 4.0, which is pretty good.

vicente
Posts: 195
Joined: Sun Oct 07, 2007 12:24 am

Post by vicente » Thu Nov 08, 2007 8:58 pm

What is your class average

Although it is true that most U.S. schools take A- to be 90-93% and A to be 93-96% and A+ to be 97-100%, many U.S. schools have crazy mark inflation. I know that the average mark in my physics classes at U of T is around 69%, which would be a D+ if you used the American percentage conversion scale. I think most American schools have an average in the low to mid 80's (a "B" to them).

So you should probably include what your class average is. What school do you go to? If you go to UBC, McGill, or U of T, I would consider that you have a perfect 4.0, or at least a 3.9+ if you have marks below 85.

tomar
Posts: 19
Joined: Thu Nov 08, 2007 5:28 pm

Post by tomar » Thu Nov 08, 2007 9:11 pm

Hi again, thanks for your replies. I go to the University of Waterloo. Our averages vary, usually I think it is around 75%, some courses are higher, some lower.

And yeah, the US conversion scale of A being 93-96 is pretty high, that way very very few would ever get A's here. So when I apply, should I just put my %, and assume they know the conversion?

User avatar
grae313
Posts: 2296
Joined: Tue May 29, 2007 8:46 pm

Post by grae313 » Thu Nov 08, 2007 11:09 pm

I was filling out a grad school application and they had a pdf worksheet for calculating your gpa, and on it they had a conversion table for schools that use percentages. I looked but I don't remember which school had this. I think I remember that if you were in the top 5% of your class it was an A+.


The easiest thing would be to just call up one of the schools you want to go to. It's anonymous, and they'll tell you right away how to convert it. No guessing.

kyros
Posts: 5
Joined: Thu Oct 25, 2007 12:30 am

Post by kyros » Sat Nov 10, 2007 9:14 pm

My school apparently does do some level of conversion prior to sending out my transcript - 4.33 -> 90%+ in a course, ext. It sounds like alot of schools in the states are doing nasty grade inflation if they need to set the bar for an A that high.

schandre
Posts: 55
Joined: Fri Nov 09, 2007 3:43 pm

Post by schandre » Fri Dec 21, 2007 3:58 pm

I keep wondering how the admission committees will look at my undergraduate records. I am from Brazil and here during undergraduate studies we are graded on a 0 to 10 scale on 0.5 point increments and on graduate studies we are graded just like in the US, in a 0 to 4 scale with 1 point increments.

My GPA for undergraduate studies is 7.97, which looks pretty bad compared to someone from an American institution with a GPA greater than 3.0, but is outstanding for the Physics program I attended, where less than 20% of the people who start the program actually finish it and only around 5% manage to do it without failing a single class.

In my MS studies, in the same University, my GPA was 3.83, the only class I failed to get an A being the one the professor asked me if I thought I deserved it. I hope my Master's GPA, Physics GRE and research experience will help erase the bad impression that the 7.97 will surely cause.

rohan
Posts: 26
Joined: Fri Nov 09, 2007 3:05 am

Post by rohan » Sat Dec 22, 2007 3:41 am

((ure percentage/10) -2 )/2

User avatar
grae313
Posts: 2296
Joined: Tue May 29, 2007 8:46 pm

Post by grae313 » Sat Dec 22, 2007 5:14 am

no way, rohan. that assumes a 4.0 is 100%, but we all know you can get a 4.0 with a much lower percentage than that. That puts an A- at 94%

rohan
Posts: 26
Joined: Fri Nov 09, 2007 3:05 am

Post by rohan » Sat Dec 22, 2007 5:27 am

hmmm... then how do you convert the percentages to a gpa??? because, at least at my college... the grades depend on the profs... so you could get an A for something like 35% too :P ... i guess you had simply report the scores as a percentage... and the schools would take care of conversions

User avatar
grae313
Posts: 2296
Joined: Tue May 29, 2007 8:46 pm

Post by grae313 » Sat Dec 22, 2007 7:42 pm

I've seen apps that ask you to convert them yourself if your school goes by percentages. But really, this is all pretty pointless. Just call up one of the schools you are applying to and ask!



Post Reply